Size calculator

How Much Gravel for a 20x20 Area?

Calculate cubic yards, tons, and bags for a 20 by 20 foot area at any depth and material type.

Quick Answer: 20x20 Gravel by Depth

Here are the most common base quantities for a 20x20 foot area (400 square feet) using general gravel at 2,700 lb/yd³ density and 50 lb bags:

DepthCubic FeetCubic YardsTons (US)50lb Bags
2 inches672.473.33134
3 inches1003.705.00200
4 inches1334.946.67267
6 inches2007.4110.00400

These are base quantities for the specified finished depth. They show the geometric volume of that layer and exclude any additional waste or compaction allowance. A 20x20 footprint is four times the area of a 10x10, so it uses four times the material of that smaller size at the same depth. If you expect settlement or spillage, add an overage on top — see the worked example below. Figures use a default density of 2,700 lb/yd³. Different gravel types weigh differently — use the calculator on the homepage or check the density guide for material-specific weights.

Embedded Calculator

The 20x20 quantities on this page are precalculated for a fixed 400 square foot footprint at 2,700 lb/yd³. For a live answer on this footprint and any other size, use the GravelScope calculator.

How to Calculate Gravel for a 20x20 Area

The calculation follows five steps: find the area, convert depth to feet, multiply to get volume, then convert that volume to cubic yards and to tons.

Calculate area: 20 ft × 20 ft = 400 square feet
Convert depth to feet: Divide inches by 12. For 4 inches: 4 ÷ 12 = 0.333 ft
Multiply area × depth: 400 × 0.333 = 133.3 cubic feet
Convert to cubic yards: 133.3 ÷ 27 = 4.94 cubic yards
Convert to tons: 4.94 × 2,700 ÷ 2,000 = 6.67 tons

These five steps give the base quantity for a finished depth. They do not include any waste or compaction allowance.

For metric users: 6.10m × 6.10m at 10cm depth = 3.72 cubic meters = approximately 5.95 tonnes of general gravel (using 2,700 lb/yd³, which is about 1,602 kg/m³).

Worked Example: 20x20 Driveway or Parking Pad

Here is a complete worked example for a typical driveway or parking-pad application. This example targets a 4-inch finished depth, so it spreads a deeper 5-inch loose layer to allow for settlement. That is why its figures differ from the 4-inch row in the table above.

  1. Area: 20 ft × 20 ft = 400 sq ft
  2. Target finished depth: 4 inches (standard for light vehicle traffic)
  3. Compaction factor: 15% settlement expected
  4. Loose depth to spread: 4 ÷ 0.85 = 4.7 inches (round to 5 inches)
  5. Volume: 400 × (5/12) = 166.7 cubic feet = 6.17 cubic yards
  6. Weight (general gravel): 6.17 × 2,700 = 16,667 lb = 8.33 tons
  7. Add 10% allowance for waste: 8.33 × 1.10 = 9.17 tons
  8. Final order: approximately 9.2 tons or 6.2 cubic yards

This example shows why simply calculating the geometric volume is not enough. The compaction factor and waste allowance both increase the order quantity above the bare minimum. On a 20x20 area those differences are large in absolute terms, so it is worth confirming the depth you actually need before ordering.

Bag counts follow the same weight-based method used by the calculator on the homepage: divide the unrounded total weight by the bag size and round up to the next whole bag. At the 5-inch loose depth used above (166.7 cubic feet, 16,667 lb at 2,700 lb/yd³) that is 16,667 ÷ 50 = 333.3 bags, which rounds up to 334 bags. For an area this size, bagged gravel is rarely practical — bulk delivery by the ton or cubic yard is almost always cheaper and faster.

Material Variations for 20x20

Different gravel types have different densities, which changes the weight estimate while the volume stays the same. Here is how a 4-inch depth in a 20x20 area compares across common materials:

MaterialDensity (lb/yd³)Cubic YardsTons50lb Bags
Pea gravel2,5654.946.33254
Crushed stone2,7004.946.67267
General gravel2,7004.946.67267
Granite gravel2,7814.946.87275
River rock2,7004.946.67267

The volume (4.94 cubic yards) is identical for all materials at this depth. Only the weight and bag count change. Bag counts are weight-based, exactly as in the calculator on the homepage. All densities here are loose, dry planning estimates — a named supplier's published bulk density takes precedence for a real order — and granite is listed separately at the published 103 lb/ft³ (2,781 lb/yd³) broken-granite figure. Use the calculator on the homepage with your specific material to get the exact figures for your project.

20x20 Area Use Cases

A 20x20 foot area is a common size for residential projects that need more room than a small path or bed. Here are typical applications and recommended depths:

ApplicationRecommended DepthEstimated VolumeEstimated Weight
Decorative garden area2-3 inches2.47-3.70 yd³3.33-5.00 tons
Pathway and patio surround3-4 inches3.70-4.94 yd³5.00-6.67 tons
Patio base4-6 inches4.94-7.41 yd³6.67-10.00 tons
Single or double driveway4-6 inches4.94-7.41 yd³6.67-10.00 tons
Parking pad or hardstanding6-8 inches7.41-9.88 yd³10.00-13.33 tons

Always match the depth to your intended use. A decorative area at 6 inches deep uses three times the material of the same area at 2 inches, so choosing the right depth saves both money and effort. For structural uses such as a driveway, follow local construction guidance and your supplier's recommendations rather than relying on a calculator alone.

Tips for Accurate 20x20 Estimation

  • Measure twice. Verify both dimensions before calculating. A 20x20 area might actually be 19.5x20.5 due to irregular boundaries, which changes the area by about 5%.
  • Account for compaction. If you need a finished depth of 4 inches, order for approximately 4.5-5 inches loose to allow for 10-20% settlement during compaction.
  • Check ground conditions. Soft or uneven ground may require additional material to fill low spots after the base layer is placed. On a large footprint, this can add a noticeable amount.
  • Add a waste allowance. A 5-10% overage covers spillage, edge trimming and minor measurement errors without significantly increasing cost.
  • Plan for delivery access. A 20x20 area needs several tons of material. Confirm the truck can reach the site and consider where the load will be tipped.
  • Compare supplier quotes. Get prices from at least 2-3 suppliers and compare on the same unit basis (tons vs cubic yards). Delivery and minimum order quantities often change the cheapest option.

Related Calculators and Guides

Common Questions

How much gravel for a 20x20 area?

For a 20x20 area at 4 inches deep with general gravel, you need 4.94 cubic yards or 6.67 tons. This covers a 400 square foot area, a common size for large patios, double driveways and parking pads.

How many cubic yards of gravel for 20x20 at 3 inches deep?

For a 20x20 area at 3 inches deep, you need 3.70 cubic yards of gravel. Calculation: (20 × 20 × 3/12) ÷ 27 = 3.70 cubic yards.

How many tons of gravel for a 20x20 driveway?

For a 20x20 driveway at 4 inches deep with general gravel (2,700 lb/yd³), you need 6.67 tons. Add 10% for compaction and waste: 7.33 tons total.

What depth of gravel is best for a 20x20 patio?

For a 20x20 patio, 4-6 inches of compacted gravel is recommended for durability. This translates to 4.94-7.41 cubic yards of gravel, or about 6.67-10.00 tons for general gravel, depending on stone type.

How many bags of gravel for a 20x20 area?

For a 20x20 area at 4 inches deep, you need 267 bags of 50lb gravel. At 6 inches deep, you need 400 bags. Bag counts are based on weight: at 2,700 lb/yd³ a 4-inch layer weighs 13,333 lb, and 13,333 ÷ 50 = 267 bags. For an area this large, loose bulk delivery is usually far more practical than bags.

Continue planning Use the gravel calculator Browse all guides 10x12 Gravel Calculator How deep should gravel be? Read the estimate disclaimer

These calculations are for material planning only. Site conditions, local standards, drainage and supplier specifications can change the correct build-up for a project.